Moog modular sequencer compliment B Walnut case.

Sequencer compliment spec.

• Sequencer Complement B Modules
• 2x 960 Sequential Controllers
• 1x 961 Interface
• 2x 962 Sequential Switch
• 1x 994 Dual Multiples Panel
• Weights and Dimensions
• Main Cabinet
• Weight: 60 lbs
• Dimension: 48 ½” wide x 15 ½” high x 14” deep
• Power
• Powered by main console
• Modules And Their Original “Functional Descriptions”.
• 960 Sequential Controllers: The 960 Sequential Controller has a wide variation of functions, both as an independent module and in combination with the 961Interface and 962 Sequential Switch.
• The sequencer module consists of a voltage controlled clock oscillator, which drives three rows of eight steps each. Indicatorlights show sequence and step position status. A separate potentiometer for each step permits up to eight different voltage settings to be selected for each row. The DC voltage output corresponds to the column of pots below the lighted stage. Voltagerange switches for each row determine the DC voltage range ofeach pot with two volts {X1}, four volts {X2}, or eight volts{X4} maximum extent. Two parallel outputs are provided for eachrow. Jacks for trigger inputs and outputs appear below each column. Trigger inputs activate that stage independently of theclock oscillator trigger. Trigger outputs are available for anyother V-trigger activated input. Manual trigger buttons as well,are included for each of the eight stages {found below the V-trigger jacks}. Switches found immediately below each step position permit normal, skip or stop functions. A ninth positionproviding skip {continuous progression through the eight steps}or stop {one progression to closure} functions is included at theend of the row. Timing control for the eight steps is accomplished via the Third Row Control of Timing switch. This switchconnects the third row of the sequencer into the control input ofthe clock speed for each stage according to the settings on thethird row potentiometers. The Shift input admits an externalclock input to the sequencing circuit. This input may be used inaddition to or exclusive of the internal clock oscillator trigger. Manual shift from step to step is accomplished with the button next to the shift input jack, as well as individual manual trigger buttons for each step found under each step column.
• Manual buttons or external v-trigger sources initiate the clock oscillator start and stop functions. The clock oscillator is capable of producing frequencies from .1Hz to 1kHz. It has both octave {range} and vernier {fine adjust} controls. One control input jack is available, as well as one rectangular wave output {approximately 90/10% duty cycle}. The clock oscillator, like other Moog oscillators, is standardized to one volt per octave.
• 961 Interface: Four independent circuits are found on the 961 Interface: one Audio-In to V-trigger Out circuit, one S-trigger In to V-Trigger Out circuit, and two V-trigger In to S-trigger Out circuits. All interface circuits may be used simultaneously, in combination, or separately.
• The Audio to V-trigger circuit generates V-triggers when the audio input level rises above the threshold set on the Sensitivity potentiometer. This V-trigger sensitivity varies with the frequency band of the audio signal and with the frequency of its amplitude peaks. V-trigger duration is commensurate with the length of time the audio signal remains above the sensitivity threshold. Two parallel V-trigger outputs are included.
• The S-trigger to V-trigger circuits converts any Short-to-ground trigger input to a v-trigger output.
• Each V-trigger In to S-trigger Out circuit has two columns of six jacks each for input triggers and one S-trigger output. Column A of the V-trigger inputs will convert V-trigger signals to S-triggers with duration equal to the input. Column B determines S-trigger duration by the Switch-on-time knob ONLY. B Column S-triggers will block, extend or fore-shorten Column B V-trigger inputs to conform to whatever duration is indicated on the B-column potentiometer. A minimum switch-on-time of 40 milliseconds and maximum time of 4 seconds duration is available. Simultaneous inputs to both A and B columns may be made. Simultaneous inputs to two parallel jacks will result in the longer of the two trigger signals being accepted.
• 962 Sequential Switch: The 962 Sequential Switch selects between two or three signal inputs, coupling one signal to the output jack at a time. A V-trigger pulse introduced to the Shift Input initiates the sequence. The Sequential Switch will alternate between stages One and Two, disregarding stage three until a standard {tip-sleeve} phone plug is patched into Signal Input Three. A connection to Input Three will cause the Sequential Switch to alternate between the three stages {in order) when triggered. Separate V-trigger input and output jacks are provided far each of the three stages, as well as buttons for manual switching. A small light for each stage indicates its status, on {coupled to the output} or off.
• 994 Dual Multiples Panel: The multiple is a device, which permits multiple distribution of one signal to several different places. This process is often called signal splitting. Multiples are used for many purposes; from linking two patch cords together, sending a single signal to several different modules at the same time, to doubling or trebling the amplitude of a signal by sending it X3 to a particular source.